Patton electronic 4020 Series User Manual Page 95
- Page / 98
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Introduction 95
SmartLink 4020 Getting Started Guide C • Dial plans
Introduction
The MGCP and SIP code will allow provisioning (via web browser) of the dial plan. A dial plan gives the unit
a map to determine when a complete number has been entered and should be passed to the SIP server or gate-
keeper for resolution into a destination IP address. Dial plans are expressed using the same syntax as used by
MGCP NCS specification.
The formal syntax of the dial plan is described by the following notation:
Digit ::= "0" | "1" | "2" | "3" | "4" | "5" | "6" | "7" | "8" | "9"
Timer ::= "T" | "t"
Letter ::= Digit | Timer | "#" | "*" | "A" | "a" | "B" | "b" | "C" | "c"| "D" | "d"
Range ::= "X" | "x" -- matches any digit
| "[" Letters "]" -- matches any of the specified letters
Letters::= Subrange | Subrange Letters
Subrange::= Letter -- matches the specified letter
| Digit "-" Digit -- matches any digit between first and last
Position::= Letter | Range
StringElement::= Position -- matches any occurrence of the position
| Position "." -- matches an arbitrary number of occurrences
including 0
String ::= StringElement | StringElement String
StringList::= String | String "|" StringList
DialPlan::= String | "(" StringList ")"
A dial plan, according to this syntax, is defined either by a (case insensitive) string or by a list of strings. Regard-
less of the above syntax a timer is only allowed if it appears in the last position in a string (12T3 is not valid).
Each string is an alternate numbering scheme. The unit will process the dial plan by comparing the current dial
string against the dial plan, if the result is under qualified (partial matches at least one entry) then it will do
nothing further. If the result matches or is over-qualified (no further digits could possibly produce a match)
then send the string to the gatekeeper and clear the dial string. The Timer T is activated when it is all that is
required to produce a match. The period of timer T is 4 seconds. For example a dial plan of (xxxT|xxxxx) will
match immediately if 5 digits are entered, it will also match after a 4 second pause when 3 digits are entered.
Sample Dial Plans
Simple Dial Plan
Allows dialing of 7-digit numbers (e.g. 5551234) or an operator on 0. Dial plan is (0T|xxxxxxx)
Non-dialed Line Dial Plan
As soon as handset is lifted the unit contacts the gatekeeper (used for systems where DTMF detection is done
in-call). Dial plan is (x.) i.e. match against 0 (or more) digits. Note: the dot ‘.’
Complex Dial Plan
• Local operator on 0, long distance operator on 00
• 4-digit local extension number starting with 3, 4, or 5
• 7-digit local numbers are prefixed by an 8
- SmartLink 4020 1
- Summary Table of Contents 3
- Table of Contents 4
- List of Figures 13
- List of Tables 15
- About this guide 16
- Precautions 17
- General observations 18
- General conventions 18
- Chapter 1 19
- General information 19
- SmartLink 4020 overview 20
- Chapter 2 21
- SmartLink installation 21
- Installing the router 22
- Installing the router 23 23
- Chapter 3 Home 24
- System information 25
- System Status 26
- Chapter 4 Network—WAN 27
- Status 29 29
- Settings 30
- Internet Configuration 31
- Device Operating Mode 31
- Specify fixed WAN configuration 31
- WAN PPPoE Configuration 32
- Enable PPPoE 32
- Authentication 32
- Dynamic DNS 32
- Configuring Dynamic DNS 33
- MAC Spoofing Configuration 33
- WAN MAC Address (Spoofed) 33
- Settings 34 34
- QoS (Quality of Service) 35
- ToS/DiffServ 35
- IPSec Configuration 36
- IPSec Configuration 37 37
- Saving your work 38
- Chapter 5 Network—LAN 39
- Add button 41
- Dynamic Routing 42
- Static Routing 42
- Viewing the Routing Table 42
- Port Forwarding 43
- IP Filtering 43
- Filter IP Range 44
- Chapter 6 Telephony 45
- VoIP Status 48
- User Name 49
- Caller ID Setting 49
- Subscribed for Voicemail 49
- Messages waiting 49
- SIP Configuration 50
- SIP Server Settings 50
- Gateway Settings 50
- SIP Parameters 52
- Hook Flash MIME Type 52
- RTP Parameters 52
- Audio/CODEC Configuration 54
- Phone 1 & Phone 2 55
- Phone 1 & Phone 2 56 56
- Phone 1 & Phone 2 57 57
- Phone 1 & Phone 2 58 58
- Phone 1 & Phone 2 59 59
- Phone 1 & Phone 2 60 60
- Speed Dial 61
- Chapter 7 System 62
- Set Security Password 65
- Configuration 66
- Enable Debug 67
- Debug Server 67
- Debug Connect Port 67
- Service Access 68
- Localization 68
- Call Progress Tones 69
- Dial Tone 69
- Prompt Tone 69
- Confirm Tone 69
- Holding Tone 69
- Busy Tone 70
- Ring Back Tone 70
- Off Hook Warning 70
- Distinctive Ring Setting 1–8 70
- Supplementary Service Keys 71
- Localization 72 72
- Localization 73 73
- Localization 74 74
- Localization 75 75
- Localization 76 76
- SNMP Configuration 77
- Auto Upgrade 78
- Manual Upgrade 79
- Figure 54. Reload window 80
- Chapter 8 Documentation 81
- Introduction 82
- Chapter 9 Logout 83
- Introduction 85 85
- Chapter contents 86
- Contact information 87
- Out-of-warranty service 88
- Returns for credit 88
- Return for credit policy 88
- RMA numbers 88
- Shipping instructions 88
- Compliance 90
- Radio and TV Interference 90
- Appendix B Specifications 91
- Voice Connectivity 92
- Connectivity 92
- Fax and Modem Support 92
- Voice Services/Features 93
- IP Services 93
- Management 93
- Operating Environment 93
- Appendix C Dial plans 94
- Sample Dial Plans 95
- Dial plan for this is: 96
- Appendix D Calling Features 97
Related products and manuals for Networking Patton electronic 4020 Series
Networking Patton electronic 29XX User Manual
(326 pages)
(326 pages)
© 2020, manymanuals.com. All rights reserved. | 4.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals